I’m a bit embarrassed to write this post. That’s because I have to show you my very first woodworking project ever, a garbage can for the kitchen. It all started one fateful autumn day where I was getting fed up with taking out the garbage. You see, we had one of those stainless steel garbage cans in our kitchen from Target and I wasn’t particulary fond of it. Not only did the plastic lid break, it wasn’t big enough which meant frequent garbage bag trips. My biggest gripe was that it sucked! I mean literally. It would suck on the garbage bag so hard we would need two people to pull the bag out, as if we were taking away its precious pearls. I could have just bought a better garbage can but that’s no fun. And so, my woodworking journey began.
I began researching garbage can designs. It’s quite sad that garbage cans became my hobby, but it made me happy. I drew out a bunch of different designs and I ended up with this one. Being this early in my woodworking career, I built it with only a drill and a jigsaw.
Check out the custom made garbage liner clamps. There are hooks on the left to hold separate grocery bags where you can throw in your recyclables. Also, there are vertical felt and foam strips on the far sides to seal in the garbage odor. Man, I should go into marketing.
No more heavy lifting needed. The cabinet opens up so you can just pull it out on the side. Ingenious, if I do say so myself…
Luckily my wife didn’t mind this ugly beast sitting in our kitchen. After all, it did serve its purpose well and enabled her to take out the garbage by herself without my help. I remember it took me a couple weeks to build this since I didn’t have much equipment. Now, I could probably crank this baby out in a couple days.
After using the cabinet for about a year, my mind started wandering. My pet peeves started bothering me like the fact that it was ugly. The top loading design meant that the lid would slam down if you weren’t careful. The door popped open and wouldn’t stay shut. Did I mention that it was ugly?
So my garbage research began again and I started playing around with new designs. Here are some of my notes.
I started out with the front face of the cabinet. I figured this would be the hardest part so I wanted to do it first while I had plenty of energy and was really enthusiastic about the project.
This is the mechanism I crafted to make the raised panel cuts. Also pictured is my new toy, a Rigid 15-amp 10-inch heavy-duty table saw.
This took about a week to make mainly because it was my first time cutting a raised panel and I had to make a bunch of prototypes before doing it for real.
I made one big mistake. I mean, I always make mistakes in my projects but this one was like throwing an interception in the 4th quarter. Basically my plans called for 1/2 inch MDF but when I went to get the wood at Home Depot, it was late and they had run out of the 1/2 inch pieces. I only saw one option for MDF so I bought it without giving a second thought. Turned out it was 3/4 inch MDF. I only realized it after building the internal compartment and the measurements didn’t add up. Ugh.
This meant I had to redo my design and change some measurements on the fly as I was building. In the end, it came out better because the thicker material allowed deeper angled cuts but it was pretty stressful at the time.
Here is the raised panel roof. 
I used Blum Tandem Soft Close Drawer Slides. They are “high-end” drawer slides that have something called Blumotion. There’s video of the soft close at the end of this post, it’s pretty cool.
Locking hook for the internal compartment.
First coat of paint done!
So sexy.
Rails installed on the outer shell.
I didn’t plan on doing the top like this. Originally I was just going to have a flat top and use a router to do the edges. This came out better than I pictured in my head. Correction, this turned out sexier than I pictured in my head.
A magnificent beast.
The wife picked out the handle. I like the modern look it gave to the cabinet.
Light blue internal compartment to give some contrast to the white.
A throwback design decision to my first cabinet. No more heavy lifting. Always wise to make things easy for the wife.
What’s this!? A last minute design change.
It’s a garbage cinch! One of the many features I ran across in my deep research of garbage cans. It keeps the garbage bag wrapped tightly around the rim of the can.
Here’s me showing how sturdy the cabinet is. I made extra effort to make the outer compartment strong and solid enough to throw around. This ain’t no IKEA furniture!
It took me the whole summer to finish this project. It was both a source of stress and a reliever of stress. I already have some ideas on how to improve it but for now, I need to just sit back and enjoy it. I love how it can be placed anywhere in the house and it just looks like it belongs there. The 2.5 or 3.0 version isn’t officially on the roadmap…yet.
And last but not least, the kitchen cabinet door in action.
[gigya src=”http://www.youtube.com/v/OxZeGrjAroo?rel=0″ type=”application/x-shockwave-flash” allowscriptaccess=”always” allowfullscreen=”true” width=”480″ height=”385″]







































































